User Tools

Site Tools


nethserver-transmission

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
nethserver-transmission [2015/05/21 23:39]
stephdl [Reach Url]
nethserver-transmission [2019/06/05 21:48] (current)
Line 8: Line 8:
     We don't track our users, and our website and forums have no third-party ads or analytics.      We don't track our users, and our website and forums have no third-party ads or analytics. 
  
-Easy.+**Easy**.
  
 Transmission is designed for easy, powerful use. We've set the defaults to "Just Work" and it only takes a few clicks to configure advanced features like watch directories, bad peer blocklists, and the web interface. When Ubuntu chose Transmission as its default BitTorrent client, one of the most-cited reasons was its easy learning curve. Transmission is designed for easy, powerful use. We've set the defaults to "Just Work" and it only takes a few clicks to configure advanced features like watch directories, bad peer blocklists, and the web interface. When Ubuntu chose Transmission as its default BitTorrent client, one of the most-cited reasons was its easy learning curve.
  
 ====Installation==== ====Installation====
-Add my repository +Add my repository, [[nethserver|see how to do it]]
- +
-  yum install http://mirror.de-labrusse.fr/NethServer/6/noarch/nethserver-stephdl-1.0.0-1.ns6.noarch.rpm+
  
 then install the module then install the module
  
-  yum install nethserver-linux-dash --enablerepo=stephdl+  yum install nethserver-transmission --enablerepo=stephdl
  
 after that the transmission-daemon is started, go to https://IP/transmission  after that the transmission-daemon is started, go to https://IP/transmission 
Line 25: Line 23:
  
 ====Usage==== ====Usage====
 +  * Stop the service
 if you want to stop it (enabled/disabled) if you want to stop it (enabled/disabled)
  
Line 30: Line 29:
     signal-event nethserver-transmission-save     signal-event nethserver-transmission-save
  
-Transmission is particular, it doesn't write its configuration on the fly to its settings.json, **it does at the shutdown and it reads at the boot time**, Therefore when you modify some specific settings as +  * Web application settings 
 +Transmission is particular, it doesn't write its configuration on the fly to its settings.json, **it does at the shutdown and it reads at the boot time**, Therefore when you modify some specific settings **in the web application** of transmission like 
  
   * the rpc-peer (peer port 51413 by default)    * the rpc-peer (peer port 51413 by default) 
Line 46: Line 46:
 This event will read the **/var/lib/transmission/settings.json** and accordingly to these parameters will set good values to Nethserver (eg firewall, download folder....) This event will read the **/var/lib/transmission/settings.json** and accordingly to these parameters will set good values to Nethserver (eg firewall, download folder....)
  
 +  * Manual settings
 You will find some settings in the web application, nevertheless [[https://trac.transmissionbt.com/wiki/ConfigurationParameters|if you miss some specific]] then you must edit manually the /var/lib/transmission/settings.json **but it is a mandatory**, you must stop first the daemon You will find some settings in the web application, nevertheless [[https://trac.transmissionbt.com/wiki/ConfigurationParameters|if you miss some specific]] then you must edit manually the /var/lib/transmission/settings.json **but it is a mandatory**, you must stop first the daemon
  
Line 82: Line 83:
  
 https://IP/dl-transmission https://IP/dl-transmission
 +
 +https://IP/transmission
 +
 +and think about the transmission samba share
 +
 +====DB entries====
 +
 +see the different db properties
 +  # config show transmission
 +  transmission=configuration
 +    DownloadDir=/var/lib/transmission/Downloads   #folder where save downloads
 +    TCPPort=51413               #port opened to public to allow peers to connect to transmission, set a value or set it randomly in transmission
 +    WebNameDir=dl-transmission  #Url to retrieve downloads : https://IP/dl-transmission
 +    Webaccess=private           #the web service to retrieve download is restricted to the local network (public/private)
 +    access=public               #peer port opened to public
 +    status=enabled
 +
 +and the entries relative to the daemon
 +
 +   # config show transmission-daemon 
 +   transmission-daemon=service
 +     Name=transmission     #Url to reach transmission web application https://IP/transmission
 +     TCPPort=9091          #transmission port restricted to the localhost
 +     access=none           #transmission port restricted to localhost (it exist a reverse proxy)
 +     status=enabled
 +
 +
 ==== Issues ==== ==== Issues ====
  
nethserver-transmission.1432244395.txt.gz · Last modified: 2019/06/05 21:48 (external edit)